Session Status

Due to inactivity, your session will end in approximately 2 minutes. Extend your session by clicking OK below.

Due to inactivity, your session has expired. Please sign in again to continue.

Inseego MiFi 2100 5G UW - Advanced Settings

2026-10-12 17:14:48.513

Inseego MiFi 2100 5G UW - Advanced Settings

Here's how to change advanced settings (e.g., Networks, Manual DNS, etc.) on your MiFi 2100 5G UW.
To change the advanced settings (e.g., VPN Passthrough enable, Network Name broadcast enable, etc.) on your Inseego MiFi 2100 5G UW, view this info.
Changing advanced settings may be harmful to the stability, performance, and security of the MiFi. Contact your local IT admin prior to altering any of these settings.

Networks

For info regarding APN settings, refer to Edit Access Point Name (APN).
  2. From the Settings section, click the
    Navigation arrow
     Navigation arrow (lower-right) to open the Settings page.
  3. Click the
    Advanced tab
    , review the warning then click
    Continue
    .
  4. Click
    Networks
     (located below the Advanced tab).
  5. From the Network Selection section, click the 'Allow device to connect to the mobile network'
    switch
     to turn on Switch on or off Switch off .
    If turned off, the device disconnects from the mobile network.
  6. Click the 'Enable automatic network selection'
    switch
     to turn on or off.
    5G / LTE are the automatically selected networks.
    If needed, click
    Select network manually
    Scan for Networks
    Continue
     to search for other available networks.
  7. Click
    Save Changes
    .

Manual DNS

Domain Name Server (DNS) settings are automatically assigned by the device. If turning on manual DNS is necessary, contact your local IT admin for assistance.
  2. From the Settings section, click the
    Navigation arrow
     Navigation arrow (lower-right) to open the Settings page.
  3. Click the
    Advanced tab
    , review the warning then click
    Continue
    .
  4. Click
    Manual DNS
     (located below the Advanced tab).
  5. Select
    Turn on Manual DNS
     to turn on or off.
    On when a checkmark is present.
  6. From the DNS 1 IP address and DNS 2 IP address fields, enter the appropriate info.
    'Turn on Manual DNS' must be on in order to enter info into these fields.
  7. Click
    Save Changes
    .

Firewall

  2. From the Settings section, click the
    Navigation arrow
     Navigation arrow (lower-right) to open the Settings page.
  3. Click the
    Advanced tab
    , review the warning then click
    Continue
    .
  4. Click
    Firewall
     (located below the Advanced tab).
  5. Tap the switch for any of the following to turn on Switch on or off Switch off :
    • VPN Passthrough
    • IPv6 Transparent Mode
  6. From the DMZ (IPv4) section, select
    Allow DMZ
     to turn on or off.
    On when a checkmark is present.
    If on, enter the appropriate IP address into the Destination IP address field.
  7. Click
    Save Changes
    .

LAN

  2. From the Settings section, click the
    Navigation arrow
     Navigation arrow (lower-right) to open the Settings page.
  3. Click the
    Advanced tab
    , review the warning then click
    Continue
    .
  4. Click
    LAN
     (located below the Advanced tab).
  5. From the IPv4 section, enter the desired info into the following fields:
    • IP Address
    • Subnet Mask
    • MAC Address
    • Turn on DHCP server
      On when a checkmark is present.
    • DHCP lease time
    • Start DHCP address range at
  6. From the IPv6 section, select
    Turn on IPv6
     to turn on or off.
    On when a checkmark is present.
  7. Click
    Save Changes
    .

VPN

When an OpenVPN tunnel is established, all connected device traffic is sent through the tunnel and settings such as Port Forwarding and Port Forwarding don't apply.
  2. From the Settings section, click the
    Navigation arrow
     Navigation arrow (lower-right) to open the Settings page.
  3. Click the
    Advanced tab
    , review the warning then click
    Continue
    .
  4. Click
    VPN
     (located below the Advanced tab).
  5. To begin, click
    Configure Open VPN settings
    .
  6. If needed, drag and drop files from your VPN provider into the
    Setup files box
    .
  7. Enter the username and password in to the fields.
  8. Click the Auto-connect VPN switch to turn on Switch on or off Switch off .
  9. If VPN is configured, view the Connection status and Connection time from the VPN Connection section.
    You can also click
    View log
     to view past connection info.
  10. To delete saved VPN info, click
    Clear all VPN settings
    .
  11. Click
    Save Changes
    .